MODEL T10024
ACCESSORY KIT #2
FOR T10010/T10097
WET GRINDER
INSTRUCTION SHEET
Inventory (Figure 2)
Introduction
A. universal sharpening Jig ........................... 1
b. Jig holder ................................................... 1
C. universal sharpening Jig Knobs................ 2
D. Chisel Jig.................................................... 1
E. stone dresser ............................................ 1
the model t10024 accessory Kit #2 for the model
t10010/t10097 Wet grinder helps sharpen chis-
els and dress grinding wheels.
b
a
d
C
e
Figure 2. inventory.
Figure 1. t10024 accessory Kit.
Unpacking
the model t10024 accessory Kit was carefully
packed when it left our warehouse. if you discover
any parts are damaged after you have signed
for delivery, please immediately call Customer
Service at (570) 546-9663 for advice. save the
containers and all packing materials for possible
inspection by the carrier or its agent. Otherwise,
filing a freight claim can be difficult. When you
are completely satisfied with the condition of your
shipment, you should inventory the contents.
Adhere to all safety warnings outlined in
the Model T10010/T10097 Wet Grinder user
manual. If you are not familiar with the prop-
er usage of the Model T10010/T10097 Wet
Grinder, review the procedures and safety
warnings covered in that manual. Failure to
do so could result in damage to the machine
or personal injury.
Copyright © November, 2007 by grizzly iNdustrial, iNC. revised may, 2011 (Jb)
WARNING: NO pORTION OF THIS MANUAL MAY bE REpRODUCED IN ANY SHApE
OR FORM WITHOUT THE WRITTEN AppROvAL OF GRIzzLY INDUSTRIAL, INC.
(For models maNuFaCtured siNCe 11/07) #Jb10089 priNted iN ChiNa
the chisel sharpening jig is capable of accurately
sharpening a variety of chisels. the jig must be
assembled and used differently depending on the
tool you are sharpening and the way you want it
to be sharpened.
3. Clamp the chisel (bevel-side down) into the
jig using the knob, as shown in Figure 7.
your exact clamping method may vary slightly
depending on your chisel.
To assemble the jig for beveled chisels:
1. Completely disassemble the chisel sharpen-
ing jig as shown in Figure 5.
Figure 7. Clamping bevel chisel (2-sided bevel).
4. place the assembled jig onto the universal
support, as shown in Figure 8.
Figure 5. Jig disassembled.
2. reassemble the jig and the jig holder as
shown in Figure 6.
Jig holder
Figure 8. grinding beveled chisels.
5. adjust the grinding angle by sliding the uni-
versal support in or out and by repositioning
the chisel in the jig. once the desired angle is
achieved, tilt the chisel away from the grinding
wheel, then connect the grinder to power and
turn it ON.
Chisel sharpening Jig
Figure 6. beveled chisel jig assembled.
To sharpen beveled chisels:
6. return the chisel onto the surface of the
wheel. use a firm grip on the chisel, but do not
use heavy pressure against the wheel. move
the chisel back and forth across the surface of
the wheel while grinding to prevent excessive
or uneven wheel wear.
1. disCoNNeCt griNder From poWer!
2. place the universal support in either the verti-
cal or horizontal mounts, depending on the
desired grinding action as described in the
model t10010/t10097 owner's manual.
-3-
t10024 Wet grinder accessory Kit #2
To assemble the jig for hollow chisels:
Chisel
Clamp
Chisel
pin
1. Completely disassemble the chisel sharpen-
ing jig as shown in Figure 5.
2. re-assemble the jig as shown in Figure 9.
Narrow Chisels
Wide Chisels
Figure 10. Clamping hollow chisels.
4. place the assembled jig onto the universal
support, as shown in Figure 11.
Chisel sharpening Jig
Figure 9. hollow chisel jig assembly.
To sharpen hollow chisels:
1. disCoNNeCt griNder From poWer!
2. place the universal support in either the verti-
cal or horizontal mounts, depending on the
desired grinding action as described in the
model t10010/t10097 owner's manual.
Figure 11. grinding hollow chisels.
3. Clamp the chisel (bevel-side down) into the
jig, as shown in Figure 10. No single clamp-
ing method works best for all chisels and only
trial-and-error with each specific tool will give
the best clamping orientation.
5. adjust the grinding angle by sliding the uni-
versal support and repositioning the chisel in
the jig. once the desired angle is achieved, lift
the chisel away from the grinding wheel, then
connect the grinder to power and turn it ON.
Tip: For narrow chisels, use the chisel pin to
secure the chisel, as shown in Figure 10.
6. return the chisel onto the surface of the
wheel. use a firm grip on the chisel, but do not
use heavy pressure against the wheel. rotate
the chisel to grind the entire edge.
-4-
t10024 Wet grinder accessory Kit #2
T10024 parts breakdown and List
2
5
1
14
13
3
7
12
1
4
6
8
9
11
10
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
1
2
3
4
5
6
7
PT10024001
PT10024002
KNOB M6-1 X 20
UNIVERSAL JIG
KNOB M8-1.25 X 40
CHISEL CLAMP
KNOB BOLT M6-1 X 16
CHISEL BED
8
PT10024008
JIG HOLDER
9
PFH38M
FLAT HD SCR M6-1 X 16
PHLP HD SCR M8-1.25 X 10
STONE DRESSER
PT10024003
PT10024004
PT10010010
PT10024006
PT10024007
10
11
12
13
14
PS39M
PT10024011
PT10024012
PT10024013
PN01M
CHISEL PIN
THREADED SLEEVE M12-1.75 X 45
HEX NUT M6-1
CHISEL JIG
Buy Direct and Save with Grizzly® – Trusted, Proven and a Great Value!
~Since 1983~
Visit Our Website Today For
Current Specials!
ORDER
24 HOURS A DAY!
1-800-523-4777
|